View-Master $model.subName Reparaturanleitung

V I E W – M A S T E R® P E R S O N A L S T E R E O C A M E R A R E P A I R M A N U A L J U L Y 1 9 5 4

keyed pinion shaft. Test for freeness. If not perfectly free replace pinion 118-545. 3.150 Turn dials to F/6.3 and 1/58. Turn exposure dial to “B

7.000 FLASH TROUBLES 7.100 Flash Bulb Will Not Fire It is best to check with another flash unit, as the trouble may be in the flash unit or in t

film being scratched before processing. Polish film channel lightly with crocus cloth to cure scratches on emulsion side. Great care must be taken

P A R T T W O 20.000 BOTTOM AND BACK 20.100 To Remove Bottom and Back Be careful not to disturb switch or movement parts. 20.110 Turn camera up

21.110 Make Following Check Using Another Camera As A Standard A - Wind gears both directions to be sure 510 assembly rotates in a clockwise direct

R - Insert another 2-56 X ¼ in. Round head screw. Tighten this screw with solid screwdriver. S - Lubricate advance indicator threads with CD33.

J - Pull shutter blade back a little ways and install crank assembly 118-524. Crank assembly must be indexed in teeth of selector plate so that whe

In” round head screw holding small escapement to movement plate. D - Remove 2-65 X ¼ In” round head screw and 188-255 spacer at the other end of mov

Shutter Timing and Flash Synchronization ( For strobe see section 24.200 ) 24.000 SHUTTER TIMING AND FLASH SYCHRONIZATION The personal camera

P E R S O N A L C A M E R A REPAIR MANUAL This manual is made up of two parts, part one (Sections 1.000 – 8.000) Set up is the following form for

After adjusting the floating lever hook, replace camera in tester and wind camera. Trip shutter. Read timer scale. H - When tripping the shutter d

oscilloscope pictures shown in sections 24.100 – I. The camera shutter normally blocks the light from the photocell, and oscilloscope spot moves ove

as it occurs during an untimed period in the shutter operation. However, the upward spike marks the instant the switch starts to close and therefore

over the front side of the shutter blade ear. - - It must be safely rearward. M - Check to see that drive blade has ample tension to open contacts a

The rear blade which cover the lenses and terminates the exposure, will be shown by the line “E” to “F”. If the blade is uniformly slow, the picture

P E R S O N A L C A M E R A REPAIR INSTRUCTIONS 1.000 SHUTTER The vast majority of all shutter repairs may be made by lubricating RATCHET wheel

1.124 Pawl Tension Check tension of 084 pawl. It must have enough tension to engage the 082 latch every time (Min. 7 grams, Max. 15 grams). If te

1.340 Overtravel movement You will note while winding the camera that just short of half way in the winding cycle the 112 release lever pawl engage

Written by Dave Hitchcock

assembly and 020 pinion gear. The 510 pawl assembly may be tight and little hard to get out. On cameras under serial No. 9863, Install new 020 pin

movement plate, or some other interference with the 522 reset lever. Increase clearance by very carefully prying up on movement with screwdriver. T

2.420 Winding Knob Will Not Lock After One Complete Turn Check to see which position (A or B) that camera winds through in. Leave selector knob in

through, it is necessary to replace 071 slides and possibly 503 gear. Mark 551 gear, 503 gear, 534 gear, if possibly 503 gear. Mark 551 gear, 503 g